Electriq Power PowerPod 2 Installation Manual Download Page 138 | Manualshive

Page: 138 / 146

background image

138

Installation Manual

We are committed to quality and constant improvement. All specifications and
descriptions contained in this document are verified to be accurate at the time
of printing. However, we reserve the right to make modifications at any time
that may result in a change of specification without notice in our pursuit of
quality. If you find any inconsistencies or errors in this document, notify us at:

[email protected] or call (833) GO-BATTERIES

Check the resources page at www.electriqpower.com for the latest specifications
and manuals.

© 2022 Electriq Power, Inc. All rights reserved.

All information in this document is subject to copyright and other intellectual
property rights of Electriq Power, Inc. This material may not be modified,
reproduced or copied, in whole or in part, without the prior written permission
of Electriq Power, Inc. and its licensors. Additional information is available upon
request. For the latest updated list, visit www.electriqpower.com/resources/

NAME

MANUFACTURER

MODEL

TECHNICAL
DESCRIPTION

MARK(s) OF
CONFORMITY

Battery, BMS &
Main Enclosure

ZHONGNENG

LBS102100A-B02

Battery, LFP, 102.4VDC,
100Ah with BMS and
Enclosure

cETLus

Battery & Add-on
Enclosure

ZHONGNENG

200-1006

Battery, LFP, 51.2VDC,
100Ah with Enclosure

cETLus

Battery, BMS &
Main Enclosure

TOPBAND

TB103100F-
T105A_UL

Battery, LFP, 102.4VDC,
100Ah with BMS and
Enclosure

cETLus

Battery & Add-on
Enclosure

TOPBAND

350-0505

Battery, LFP, 51.2VDC,
100Ah with Enclosure

cETLus

GoodWe Inverter
(GW7600A-ES)
(includes NFT
& mounting
hardware)

GoodWe

GW7600A-ES

Hybrid Inverter,
120/240 VAC, 32
AAC, 60 HZ, PV
DC Coupled-260
to 500 VDC,
12.5/12.5/12.5/12.5
ADC

cSAus

GoodWe Inverter
(GW7600A-BP)
(includes NFT
& mounting
hardware)

GoodWe

GW7600A-BP

Hybrid Inverter,
120/240 VAC, 32
AAC, 60 HZ, PV AC
Coupled-240 VAC

cSAus

Auto-Transformer

GoodWe

GW9600A-TX

Auto-Transformer,
120/240 VAC, 40 AAC,
60 HZ

cSAus

IoT Gateway, FX30
Sierra Wireless
with EP Branding

Sierra Wireless

1104771 : FX30S-
LTEM1_1104087

4.75 to 32 VDC Input,
RS-485, LTE Cellular,
Wi-Fi IoT Gateway

cULus

Appendix / Marks of Conformity

5.9. MARKS OF CONFORMITY

«
...
136
137
138
139
140
...
»

Summary of Contents for PowerPod 2



















































































































































Reviews:

No comments

Related manuals for PowerPod 2

Brand: NEC Pages: 2

Brand: Qcells Pages: 80

Brand: Q CELLS Pages: 32

Brand: ASEA Pages: 75

Brand: JRC Pages: 10

Brand: Ableconn Pages: 15

Brand: Gorman-Redlich Pages: 3

MAXX SST VEC049GM

Brand: Vector Pages: 10

CIS-N-MPPT-LED 85/15

Brand: Phocos Pages: 79

Brand: Actox Pages: 36

Brand: BluStream Pages: 21

Brand: Cotek Pages: 48

Brand: Wavtech Pages: 12

Brand: Rheem Pages: 32

SCM9B-A1000 Series

Brand: Dataforth Pages: 8

FX-BTCVT Series

Brand: Johnson Controls Pages: 14

Brand: CYP Pages: 40

Brand: Moeller Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands