Electriq Power PowerPod 2 Installation Manual Download Page 39

Page: 39 / 146

Installation Manual

Bonding to main (10 kWh) and add-on (5 kWh) enclosure front panel
not shown. Bond between main enclosure and front panel with a PE
wire connected to marked PE PEMs.

Ensure a tooth lock washer is

used before tightening down any wing nuts or bolts.

Torque Note: 6

mm PE and battery mounting PEMs torque min. 3.3 max. 4.0 Nm (min.
2.4 max. 3.0 ft lb).

Note: Accessory bags inside the enclosure will have all the required
cables and screws.

Installing System / Battery Installation

2. Before installing the batteries, ensure the enclosure is securely

fastened and that all clearances have been adhered to as stated in
Section 3.2, 'Knockouts and Clearances'.

3. There will be four cables coming from the left and right of the

PowerHub 2, which will be wired later on into the BMS, inverter,
communications cable and front display cover.

BONDING THE BATTERY ENCLOSURE DIAGRAM

Summary of Contents for PowerPod 2



















































































































































Search results

Summary of Contents for PowerPod 2

Reviews:

Related manuals for PowerPod 2

Brands by name

Popular brands

Electriq Power PowerPod 2, Installation Manual

Search results

Summary of Contents for PowerPod 2

Reviews:

Related manuals for PowerPod 2

Brands by name

Popular brands