Dodge 2012 Grand Caravan Owner'S Manual Download Page 547 | Manualshive

Page: 547 / 695

background image

NOTE:

Remember that everything put into or on the

trailer adds to the load on your vehicle. Also, additional
factory-installed options or dealer-installed options must
be considered as part of the total load on your vehicle.
Refer to the “Tire and Loading Information” placard for
the maximum combined weight of occupants and cargo
for your vehicle.

Towing Requirements

To promote proper break-in of your new vehicle drive-
train components, the following guidelines are recom-
mended.

CAUTION!

•

Do not tow a trailer at all during the first 500 miles
(805 km) the new vehicle is driven. The engine, axle
or other parts could be damaged.

•

Then, during the first 500 miles (805 km) that a
trailer is towed, do not drive over 50 mph (80 km/h)
and do not make starts at full throttle. This helps
the engine and other parts of the vehicle wear in at
the heavier loads.

Perform the maintenance listed in the “Maintenance
Schedule.” Refer to “Maintenance Schedule” for the
proper maintenance intervals. When towing a trailer,
never exceed the GAWR or GCWR ratings.

5

STARTING AND OPERATING

545

«
...
545
546
547
548
549
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Grillo Pages: 71

Brand: Menabo Pages: 4

Brand: Metra Electronics Pages: 8

Brand: Alpine Pages: 70

Brand: Kuda-Phonebase Pages: 6

Brand: Chrysler Pages: 374

Verizon V860 - BARRAGE

Brand: AdvanceTec Pages: 8

Brand: Thule Pages: 4

Brand: Chevrolet Pages: 416

Actyon Sports 2010

Brand: SSANGYONG Pages: 76

Brand: SSANGYONG Pages: 81

Sightline RVCHN-76D

Brand: Crux Pages: 2

Brand: VBG Pages: 16

TrailerSafe 65-1060-13TK

Brand: Modernum Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands