Dodge 2012 Grand Caravan Owner'S Manual Download Page 189 | Manualshive

Page: 189 / 695

background image

WARNING!

•

Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion or other physical condition must exercise care
when using the seat heater. It may cause burns
even at low temperatures, especially if used for
long periods of time.

•

Do not place anything on the seat or seatback that
insulates against heat, such as a blanket or cushion.
This may cause the seat heater to overheat. Sitting
in a seat that has been overheated could cause
serious burns due to the increased surface tempera-
ture of the seat.

Vehicles Equipped With Remote Start

On models that are equipped with remote start, the
driver’s heated seat can be programmed to come on
during a remote start. Refer to “Remote Starting System
— If Equipped” in “Things To Know Before Starting Your
Vehicle” for further information.

Front Heated Seats

There are two heated seat switches that allow the driver
and passenger to operate the seats independently. The
controls for each heater are located on the switch bank
below the climate controls.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

187

«
...
187
188
189
190
191
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Warrior Products Pages: 2

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

Brand: Spiral Audio Pages: 2

Brand: Mazda Pages: 122

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Jaeger Pages: 16

2013 Cadillac CTS-V

Brand: Cadillac Pages: 6

Brand: Seecode Pages: 19

Brand: Cadillac Pages: 514

Brand: Thule Pages: 16

Brand: Speedsignal Pages: 13

UPSHIFT PLUS Series

Brand: SportRack Pages: 8

Brand: Hyundai Pages: 26

NEXO Fuel Cell 2019

Brand: Hyundai Pages: 17

Brand: Hyundai Pages: 230

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands