Dodge 2012 Grand Caravan Owner'S Manual Download Page 119 | Manualshive

Page: 119 / 695

background image

WARNING!

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

•

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing (CO),
follow these safety tips:

•

Do not run the engine in a closed garage or in
confined areas any longer than needed to move
your vehicle in or out of the area.

•

If you are required to drive with the trunk/liftgate/
rear doors open, make sure that all windows are
closed and the climate control BLOWER switch is
set at high speed. DO NOT use the recirculation
mode.

(Continued)

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

117

«
...
117
118
119
120
121
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Camoplast Pages: 60

Brand: Vauxhall Pages: 2

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Brand: AA Products Pages: 4

Brand: ULTIMATE SPEED Pages: 50

Brand: Hyundai Pages: 18

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: MVG Pages: 18

Brand: POOL-LINE Pages: 2

Brand: Navman Pages: 10

Brand: Macrom Pages: 10

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: Porsche Pages: 127

Brand: STO N SHO Pages: 7

Brand: Laser Pages: 3

Brand: TrailPRO Pages: 3

Brand: Hopkins Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands