Dodge 2012 Grand Caravan Owner'S Manual Download Page 573 | Manualshive

Page: 573 / 695

background image

WARNING!

(Continued)

•

Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center
where it can be raised on a lift.

•

Never start or run the engine while the vehicle is
on a jack.

•

The jack is designed to be used as a tool for
changing tires only. The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.

Jack Location

The jack, jack handle and winch handle tools are stowed
behind the rear left side trim panel in the rear cargo area.
Turn the two cover latches to release the cover.

Remove the pouch containing the scissors jack, jack
handle, and tools.

Jack And Tool Location

6

WHAT TO DO IN EMERGENCIES

571

«
...
571
572
573
574
575
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Ignition Pages: 1

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: Acura Pages: 2

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: Audi Pages: 63

Brand: v.link Pages: 19

Brand: Thule Pages: 8

Brand: Reliant Pages: 116

Brand: Tactik Pages: 4

Brand: banks Pages: 76

Brand: Kargo Master Pages: 8

Brand: HawksHead Pages: 10

Brand: ZeroRPM Pages: 41

Brand: SoundMax Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands