Dodge 2012 Grand Caravan Owner'S Manual Download Page 334 | Manualshive

Page: 334 / 695

background image

•

Electronic Speed Control SET

This light will turn on when the electronic
speed control is SET. For further information,
refer to “Electronic Speed Control” in “Under-
standing The Features Of Your Vehicle.”

EVIC Amber Telltale Lights

This area will show reconfigurable amber caution tell-
tales. These telltales include:

•

Low Fuel Light

When the fuel level reaches approximately 3.0 gal
(11.0 L) this light will turn on, and remain on until

fuel is added.

•

Loose Gascap Indicator

If the vehicle diagnostic system determines
that the fuel filler cap is loose, improperly
installed, or damaged, a loose gascap indicator
will display in the telltale display area. Tighten

the fuel filler cap properly and press the SELECT button
to turn off the message. If the problem continues, the
message will appear the next time the vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).

•

Windshield Washer Fluid Low Indicator

This light will turn on to indicate the wind-
shield washer fluid is low.

332

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
332
333
334
335
336
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

1973 Crown Hardtop

Brand: Toyota Pages: 50

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: HAUL MASTER Pages: 8

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: WABCO Pages: 52

Brand: Camoplast Pages: 19

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

Brand: Ford Pages: 15

Brand: Honda Pages: 3

Brand: ECS Electronics Pages: 42

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Brand: Ecco Pages: 2

Turnoverball 1020

Brand: Bowers & Wilkins Pages: 6

Brand: Navman Pages: 10

BUSHMAN 15L ROADIE fridge Base console

Brand: Cruiser Consoles Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands