Dodge 2012 Grand Caravan Owner'S Manual Download Page 338 | Manualshive

Page: 338 / 695

background image

Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the Menu button. To reset the oil change indicator
system (after performing the scheduled maintenance),
perform the following steps.

1. Turn the ignition switch to the ON position (do not

start the engine.)

2. Fully depress the accelerator pedal, slowly, three times

within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE:

If the indicator message illuminates when you

start the engine, the oil change indicator system did not
reset. If necessary, repeat these steps.

Fuel Economy

Press and release the UP or DOWN button until “Fuel
Economy” displays highlighted in the EVIC and press
the SELECT button. The following Fuel Economy func-
tions display in the EVIC:

•

Average Fuel Economy (AVG)

•

Distance To Empty (DTE)

•

Miles Per Gallon (MPG)

Average Fuel Economy

This display shows the average fuel economy since the
last reset. The Average Fuel Economy can be reset by
following the prompt in the EVIC to use the SELECT
button. When the fuel economy is reset, the display will
read “zero” for two seconds. Then, the history informa-
tion will be erased, and the averaging will continue from
the last fuel average reading before the reset.

336

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
336
337
338
339
340
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

MagicWatch MWE800

Brand: Waeco Pages: 212

2012 Escalade Hybrid

Brand: Cadillac Pages: 90

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: Honda Pages: 208

Brand: BMW Pages: 21

Brand: Prorack Pages: 20

Brand: Draw tite Pages: 4

Brand: Honda Pages: 569

Brand: Alphasonik Pages: 8

Brand: Pontiac Pages: 486

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Roadmaster Pages: 4

Brand: Buick Pages: 371

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands