Dodge 2012 Grand Caravan Owner'S Manual Download Page 472 | Manualshive

Page: 472 / 695

background image

temperature as well as vehicle speed. This feature im-
proves warm up time of the engine and transmission to
achieve maximum efficiency. Engagement of the torque
converter clutch is inhibited until the transmission fluid
is warm (refer to the “Note” under “Torque Converter
Clutch” in this section). During extremely cold tempera-
tures (-16°F [-27°C] or below), operation may briefly be
limited to third gear only. Normal operation will resume
once the transmission temperature has risen to a suitable
level.

Transmission Limp Home Mode

Transmission function is monitored electronically for
abnormal conditions. If a condition is detected that could
result in transmission damage, Transmission Limp Home
Mode is activated. In this mode, the transmission remains
in third gear regardless of which forward gear is selected.

PARK, REVERSE, and NEUTRAL will continue to oper-
ate. The Malfunction Indicator Light (MIL) may be illu-
minated. Limp Home Mode allows the vehicle to be
driven to an authorized dealer for service without dam-
aging the transmission.

In the event of a momentary problem, the transmission
can be reset to regain all forward gears by performing the
following steps:

1. Stop the vehicle.

2. Shift the transmission into PARK.

3. Turn the ignition switch to the LOCK/OFF position.

4. Wait approximately 10 seconds.

5. Restart the engine.

6. Shift into the desired gear range. If the problem is no

longer detected, the transmission will return to normal
operation.

470

STARTING AND OPERATING

«
...
470
471
472
473
474
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: Metra Electronics Pages: 2

Brand: FormFit Pages: 2

Brand: Hyundai Pages: 19

Brand: Skoda Pages: 281

Brand: JBL Pages: 12

Interlock 700 Series

Brand: Scania Pages: 82

Brand: TrailFX Pages: 2

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: iQOS Pages: 4

Brand: Mitsubishi Pages: 57

Brand: ACV Pages: 2

Brand: MBW Pages: 40

Indash 75114-296

Brand: Panavise Pages: 2

Brand: Air Lift Pages: 12

MULTI VEHICLE MOUNT MVM-45-05

Brand: Bracketron Pages: 4

Brand: Brodit Pages: 2

Brand: Yakima Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands