Dodge 2012 Grand Caravan Owner'S Manual Download Page 582 | Manualshive

Page: 582 / 695

background image

WARNING!

(Continued)

•

Do not let anyone sit in the vehicle when it is on a
jack.

•

Do not get under the vehicle when it is on a jack. If
you need to get under a raised vehicle, take it to a
service center where it can be raised on a lift.

•

Only use the jack in the positions indicated and for
lifting this vehicle during a tire change.

•

If working on or near a roadway, be extremely
careful of motor traffic.

•

To assure that compact spare tires, flat or inflated,
are securely stowed, compact spares must be
stowed with the valve stem facing the ground.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.

NOTE:

Refer to the “Compact Spare Tire” section of

“Tires – General Information” for information about the
compact spare tire, its use, and operation.

1. Loosen (but do not remove) the wheel lug nuts by

turning them to the left one turn while the wheel is
still on the ground.

Jack Warning Label

580

WHAT TO DO IN EMERGENCIES

«
...
580
581
582
583
584
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Acdeos Pages: 38

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Mitsubishi Pages: 160

Brand: Cadillac Pages: 442

Brand: PullRite Pages: 10

Gold Cruuse Cruisecontrol GC90

Brand: John Gold Pages: 24

Brand: Whispbar Pages: 14

Brand: Actia Pages: 37

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Linear Logic Pages: 8

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Hama Pages: 13

2005-2009 Chrysler 300C

Brand: Mopar Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands