Dodge 2012 Grand Caravan Owner'S Manual Download Page 242 | Manualshive

Page: 242 / 695

background image

To Accelerate For Passing

Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

Using Electronic Speed Control On Hills

The transmission may downshift on hills to maintain the
vehicle set speed.

NOTE:

The Electronic Speed Control system maintains

speed up and down hills. A slight speed change on
moderate hills is normal.

On steep hills, a greater speed loss or gain may occur so
it may be preferable to drive without Electronic Speed
Control.

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions, and you
could lose control and have an accident. Do not use
Electronic Speed Control in heavy traffic or on roads
that are winding, icy, snow-covered or slippery.

PARKSENSE® REAR PARK ASSIST — IF
EQUIPPED

The ParkSense® Rear Park Assist system provides visual
and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to “ParkSense® Sys-
tem Usage Precautions” for limitations of this system and
recommendations.

240

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
240
241
242
243
244
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: iDataLink Pages: 9

Brand: B-Speech Pages: 24

Brand: U & Me Brothers Pages: 6

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

Brand: MVG Pages: 18

Brand: Honda Pages: 124

Brand: Thule Pages: 4

Brand: Ford Pages: 52

Brand: Mitsubishi Pages: 362

Brand: Mobridge Pages: 20

Brand: Mopar Pages: 17

Brand: Prorack Pages: 13

Brand: iQOS Pages: 4

Brand: Lexus Pages: 6

Brand: Edelbrock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands