Dodge 2012 Grand Caravan Owner'S Manual Download Page 247 | Manualshive

Page: 247 / 695

background image

WARNING ALERTS

Rear Distance

(in/cm)

Greater than

79 in (200 cm)

79-39 in

(200-100 cm)

39-25 in

(100-65 cm)

25-12 in

(65-30 cm)

Less than

12 in (30 cm)

Audible Alert

Chime

None

Single 1/2

Second Tone

Slow

Fast

Continuous

Arcs

None

3 Solid

(Continuous)

3 Slow

Flashing

2 Slow

Flashing

1 Slow

Flashing

Radio Mute

No

Yes

Yes

Yes

Yes

NOTE:

ParkSense® will MUTE the radio, if on, when the

system is sounding an audio tone.

Enabling/Disabling ParkSense®

ParkSense® can be enabled and disabled through the
Customer-Programmable Features section of the EVIC.
The available choices are: OFF, Sound Only, or Sound and
Display. Refer to “Electronic Vehicle Information Center

(EVIC)/Personal Settings (Customer-Programmable Fea-
tures)” in “Understanding Your Instrument Panel” for
further information.

When ParkSense® is disabled, the instrument cluster will
display the “PARK ASSIST SYSTEM OFF” message for
approximately five seconds. Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding Your
Instrument Panel” for further information. When the
shift lever is moved to REVERSE and the system is

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

245

«
...
245
246
247
248
249
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Neuspeed Pages: 2

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Park-Daddy Pages: 22

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: TrailFX Pages: 2

Brand: IOGear Pages: 38

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: ULTIMATE SPEED Pages: 56

Brand: SMART Pages: 26

ActiveStart ACS30P

Brand: Active Controls Pages: 2

Brand: Myenergi Pages: 36

2013 Civic Sedan

Brand: Honda Pages: 368

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands