Dodge 2012 Grand Caravan Owner'S Manual Download Page 599 | Manualshive

Page: 599 / 695

background image

TOWING A DISABLED VEHICLE

This section describes procedures for towing a disabled
vehicle using a commercial wrecker service.

Towing Condition

Wheels OFF the Ground

ALL MODELS

Flat Tow

NONE

If transmission is operable:

•

Transmission in

NEUTRAL

•

25 mph (40 km/h)

max

speed

•

15 miles (24 km)

max

distance

Wheel lift

Rear

Front

OK

Flatbed

ALL

BEST METHOD

Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for this purpose, following equip-
ment manufacturer’s instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to

main structural members of the vehicle, not to bumpers
or associated brackets. State and local laws regarding
vehicles under tow must be observed.

If you must use the accessories (wipers, defrosters, etc.)
while being towed, the ignition must be in the ON/RUN
position, not the ACC position.

6

WHAT TO DO IN EMERGENCIES

597

«
...
597
598
599
600
601
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: IAG Pages: 3

Brand: Conrad Pages: 26

2003 Thunderbird

Brand: Ford Pages: 200

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

Brand: Dometic Pages: 158

Brand: Menabo Pages: 12

Brand: Ecco Pages: 12

Brand: NanoCam Plus Pages: 32

Brand: ICON Pages: 4

Brand: Ford Pages: 40

Brand: ROADGEAR Pages: 2

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: Blue Ox Pages: 9

Brand: Volkswagen Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands