Dodge 2012 Grand Caravan Owner'S Manual Download Page 592 | Manualshive

Page: 592 / 695

background image

4. Refer to “Torque Specifications” in this section for

proper wheel lug nut torque.

5. After 25 miles (40 km) check the lug nut torque with a

torque wrench to ensure that all lug nuts are properly
seated against the wheel.

JUMP-STARTING

If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.

Preparations For Jump-Start

The battery in your vehicle is located on the left side of
the engine compartment.

590

WHAT TO DO IN EMERGENCIES

«
...
590
591
592
593
594
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Mazda Pages: 4

Brand: Pivot Pages: 4

Brand: Chariot Carriers Pages: 3

Brand: Dodge Pages: 24

Brand: Ford Pages: 368

Brand: Jeep Pages: 1528

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Ferve Pages: 28

Brand: Scosche Pages: 12

Brand: Whispbar Pages: 14

Brand: Scion Pages: 58

Full Display Mirror

Brand: Gentex Pages: 18

Brand: STO N SHO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands