Dodge 2012 Grand Caravan Owner'S Manual Download Page 317 | Manualshive

Page: 317 / 695

background image

position. To turn off the message temporarily, press and
release the STEP button on the steering wheel. To reset
the oil change indicator system (after performing the
scheduled maintenance), perform the following steps.

1. Turn the ignition switch to the ON/RUN position (do
not start the engine).

2. Fully depress the accelerator pedal, slowly, three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE:

If the indicator message illuminates when you

start the engine, the oil change indicator system did not
reset. If necessary, repeat these steps.

Electronic Vehicle Information Center (EVIC) Display
— If Equipped

The Electronic Vehicle Information Center (EVIC) fea-
tures a driver-interactive display that is located in the

instrument cluster. For further information, refer to
“Electronic Vehicle Information Center (EVIC)”.

7. Anti-Lock Brake (ABS) Light

This light monitors the Anti-Lock Brake System
(ABS). The light will turn on when the ignition
switch is turned to the ON/RUN position and
may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, it
indicates that the Anti-Lock portion of the brake system
is not functioning and that service is required. However,
the conventional brake system will continue to operate
normally if the BRAKE warning light is not on.

If the ABS light is on, the brake system should be serviced
as soon as possible to restore the benefits of Anti-Lock
brakes. If the ABS light does not turn on when the
ignition switch is turned to the ON/RUN position, have
the light inspected by an authorized dealer.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

315

«
...
315
316
317
318
319
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Camcar Pages: 6

Brand: AA Products Pages: 8

SmartDiag2GO GD201-O

Brand: OCTO Pages: 5

Brand: Prorack Pages: 10

Brand: Anker Technology Pages: 8

Brand: Subaru Pages: 44

Brand: HAKR Pages: 9

Brand: Cadillac Pages: 19

Auto-Dimming Mirror

Brand: Mazda Pages: 2

Brand: Yakima Pages: 4

Brand: AA Products Pages: 6

Brand: Prorack Pages: 15

Brand: Damon Pages: 112

Brand: DV8 Pages: 14

Brand: Honeywell Pages: 16

Brand: Honeywell Pages: 70

Brand: Honeywell Pages: 70

Brand: Honeywell Pages: 398

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands