Dodge 2012 Grand Caravan Owner'S Manual Download Page 243 | Manualshive

Page: 243 / 695

background image

ParkSense® will retain the last system state (enabled or
disabled) from the last ignition cycle when the ignition is
changed to the ON/RUN position.

ParkSense® can be active only when the shift lever is in
REVERSE. If ParkSense® is enabled at this shift lever
position, the system will remain active until the vehicle
speed is increased to approximately 7 mph (11 km/h) or
above. The system will become active again if the vehicle
speed is decreased to speeds less than approximately
6 mph (9 km/h).

ParkSense® Sensors

The four ParkSense® sensors, located in the rear fascia/
bumper, monitor the area behind the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 in (30 cm) up to 79 in
(200 cm) from the rear fascia/bumper in the horizontal
direction, depending on the location, type and orienta-
tion of the obstacle.

ParkSense® Warning Display

The ParkSense® Warning screen will only be displayed if
Sound and Display is selected from the Customer-
Programmable Features section of the Electronic Vehicle
Information Center (EVIC). Refer to “Electronic Vehicle
Information Center (EVIC)/Personal Settings (Customer-
Programmable Features)” in “Understanding Your In-
strument Panel” for further information.

The ParkSense® Warning Display is located in the Instru-
ment cluster’s EVIC display. It provides both visual and
audible warnings to indicate the distance between the
rear fascia/bumper and the detected obstacle.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

241

«
...
241
242
243
244
245
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: iDataLink Pages: 99

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: kincrome Pages: 6

Brand: Nav TV Pages: 2

Brand: STO N SHO Pages: 7

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: SAN HIMA Pages: 10

SANICON TURBO 300

Brand: Thetford Pages: 25

Brand: TATA Motors Pages: 166

Brand: Advanced Diagnostics Pages: 10

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: Mitsubishi Pages: 490

Brand: Guardsman Pages: 2

Brand: Porsche Pages: 145

Brand: STO N SHO Pages: 7

Brand: Cadillac Pages: 538

BreadCrumb DX2 Series

Brand: Rajant Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands