Dodge 2012 Grand Caravan Owner'S Manual Download Page 513 | Manualshive

Page: 513 / 695

background image

WARNING!

Limited-use spares are for emergency use only. In-
stallation of this limited-use spare tire affects vehicle
handling. With this tire, do not drive more than the
speed listed on the limit-use spare wheel. Keep
inflated to the cold tire inflation pressures listed on
your Tire and Loading Information Placard located
on the driver’s side B-Pillar or the rear edge of the
driver’s side door. Replace (or repair) the original
equipment tire at the first opportunity and reinstall it
on your vehicle. Failure to do so could result in loss
of vehicle control.

Tire Spinning

When stuck in mud, sand, snow, or ice conditions, do not
spin your vehicle’s wheels above 30 mph (48 km/h) or
for longer than 30 seconds continuously without stop-
ping.

Refer to “Freeing A Stuck Vehicle” in “What To Do In
Emergencies” for further information.

WARNING!

Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause tire dam-
age or failure. A tire could explode and injure some-
one. Do not spin your vehicle’s wheels faster than
30 mph (48 km/h) for more than 30 seconds continu-
ously when you are stuck, and do not let anyone near
a spinning wheel, no matter what the speed.

Tread Wear Indicators

Tread wear indicators are in the original equipment tires
to help you in determining when your tires should be
replaced.

5

STARTING AND OPERATING

511

«
...
511
512
513
514
515
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: PAC Pages: 4

Brand: PAC Pages: 4

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: Yakima Pages: 8

Brand: Chevrolet Pages: 494

Brand: TBC Pages: 12

Brand: Safe Fleet Pages: 38

Brand: Whelen Engineering Company Pages: 9

Brand: Honda Pages: 124

Brand: r.LiNK Pages: 20

Brand: Toyota Pages: 779

Brand: Ranger design Pages: 22

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: CSL Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands