Dodge 2012 Grand Caravan Owner'S Manual Download Page 619 | Manualshive

Page: 619 / 695

background image

Refrigerant Recovery And Recycling

R-134a Air Conditioning Refrigerant is a hydrofluoro-
carbon (HFC) that is endorsed by the Environmental
Protection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by authorized dealer or other
service facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C system

PAG compressor oil and refrigerants.

A/C Air Filter

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

WARNING!

Do not remove the A/C air filter while the blower is
operating or personal injury may result.

The A/C air filter is located in the fresh air inlet behind
the glove box. Perform the following procedure to re-
place the filter:

1. Open the glove compartment and remove all contents.

2. Push in on the sides of the glove compartment and

lower the door.

3. Pivot the glove compartment downward.

4. Disengage the two retaining tabs that secure the filter

cover to the HVAC housing, and remove the cover.

7

MAINTAINING YOUR VEHICLE

617

«
...
617
618
619
620
621
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: JAC Pages: 70

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Mercedes-Benz Pages: 54

Brand: Yakima Pages: 13

Brand: MVG Pages: 18

Brand: JBL Pages: 12

Brand: Thule Pages: 4

PRIME DESIGN HRR3-E-PM52

Brand: Safe Fleet Pages: 12

Brand: TATA Motors Pages: 232

Sprinter Bed System DIY

Brand: FVC Pages: 8

Brand: Lincoln Pages: 538

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands