Dodge 2012 Grand Caravan Owner'S Manual Download Page 545

Page: 545 / 695

Trailer Towing Weights (Maximum Trailer Weight Ratings)

The following chart provides the maximum trailer weight ratings towable for your given drivetrain.

Engine/

Transmission

GCWR (Gross

Combined Weight

Rating)

Frontal Area

Max. GTW (Gross

Trailer Weight)

Max. Tongue

Weight

3.6L/Automatic

8,750 lbs (3 969 kg)

40 sq ft (3.72 sq m)

Up to 2 persons &

Luggage 3,600 lbs

(1 633 kg)*

360 lbs (163 kg)

8,750 lbs (3 969 kg)

40 sq ft (3.72 sq m)

3 to 5 persons &

Luggage 3,350 lbs

(1 519 kg)*

335 lbs (152 kg)

8,750 lbs (3 969 kg)

40 sq ft (3.72 sq m)

6 to 7 persons &

Luggage 3,000 lbs

(1 360 kg)*

300 lbs (136 kg)

* For vehicles equipped with Fold-in-Floor seating, the Gross Trailer Weight must be reduced by 100 lbs (45 kg).

Refer to local laws for maximum trailer towing speeds.

STARTING AND OPERATING

543

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Grand Caravan

Reviews:

Related manuals for 2012 Grand Caravan

Brands by name

Popular brands

Dodge 2012 Grand Caravan, Owner'S Manual

Search results

Summary of Contents for 2012 Grand Caravan

Reviews:

Related manuals for 2012 Grand Caravan

Brands by name

Popular brands