Dodge 2012 Grand Caravan Owner'S Manual Download Page 250 | Manualshive

Page: 250 / 695

background image

•

On vehicles equipped with a tailgate, ParkSense®
should be disabled when the tailgate is in the lowered
or open position and the vehicle is in REVERSE. A
lowered tailgate could provide a false indication that
an obstacle is behind the vehicle.

CAUTION!

•

ParkSense® is only a parking aid and it is unable to
recognize every obstacle, including small obstacles.
Parking curbs might be temporarily detected or not
detected at all. Obstacles located above or below
the sensors will not be detected when they are in
close proximity.

•

The vehicle must be driven slowly when using
ParkSense® in order to be able to stop in time
when an obstacle is detected. It is recommended
that the driver looks over his/her shoulder when
using ParkSense®.

WARNING!

•

Drivers must be careful when backing up even
when using ParkSense®. Always check carefully
behind your vehicle, look behind you, and be sure
to check for pedestrians, animals, other vehicles,
obstructions, and blind spots before backing up.
You are responsible for safety and must continue to
pay attention to your surroundings. Failure to do so
can result in serious injury or death.

(Continued)

248

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
248
249
250
251
252
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Mazda Pages: 4

Brand: Abarth Pages: 176

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Van Guard Pages: 3

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: AIS Pages: 2

Brand: Acura Pages: 6

Brand: ULTIMATE SPEED Pages: 10

Brand: Renault Pages: 198

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Mazda Pages: 1001

Brand: Maserati Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands