Dodge 2012 Grand Caravan Owner'S Manual Download Page 262 | Manualshive

Page: 262 / 695

background image

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)

away from the HomeLink® button you wish to pro-
gram while keeping the HomeLink® indicator light in
view.

3. Simultaneously press and hold both the HomeLink®

button you want to program and the hand-held trans-
mitter button.

4. Continue to hold both buttons and observe the indi-

cator light. The HomeLink® indicator will flash slowly
and then rapidly after HomeLink® has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.

5. At the garage door opener motor (in the garage),

locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor.

Firmly press and release the “LEARN” or “TRAIN-
ING” button. On some garage door openers/devices
there may be a light that blinks when the garage door
opener/device is in the LEARN/TRAIN mode.

NOTE:

You have 30 seconds in which to initiate the next

step after the LEARN button has been pressed.

6. Return to the vehicle and press the programmed

HomeLink® button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.

NOTE:

If the garage door opener/device does not acti-

vate, press the button a third time (for two seconds) to
complete the training.

To program the remaining two HomeLink® buttons,
repeat each step for each remaining button. DO NOT
erase the channels.

260

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
260
261
262
263
264
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Wallbox eM4 Single

Brand: ABL Pages: 68

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: AA Products Pages: 4

Brand: Metra Electronics Pages: 8

Hypercharger HYC 075

Brand: Alpitronic Pages: 64

Brand: Chevrolet Pages: 412

Brand: Fab Fours Pages: 19

Brand: Whispbar Pages: 15

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Subaru Pages: 19

Brand: Saab Pages: 15

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands