Dodge 2012 Grand Caravan Owner'S Manual Download Page 640 | Manualshive

Page: 640 / 695

background image

FUSES

WARNING!

•

When replacing a blown fuse, always use an ap-
propriate replacement fuse with the same amp
rating as the original fuse. Never replace a fuse
with another fuse of higher amp rating. Never
replace a blown fuse with metal wires or any other
material. Failure to use proper fuses may result in
serious personal injury, fire and/or property dam-
age.

•

Before replacing a fuse, make sure that the ignition
is off and that all the other services are switched off
and/or disengaged.

•

If the replaced fuse blows again, contact an autho-
rized dealer.

(Continued)

WARNING!

(Continued)

•

If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine system, gearbox system) or steering system
blows, contact an authorized dealer.

Totally Integrated Power Module

The Totally Integrated Power Module is located in the
engine compartment near the battery. Refer to the appli-
cable “Engine Compartment” illustration in this section.
This center contains cartridge fuses and mini-fuses. A
label that identifies each component may be printed or
embossed on the inside of the cover.

638

MAINTAINING YOUR VEHICLE

«
...
638
639
640
641
642
...
»

Summary of Contents for 2012 Grand Caravan
























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Grand Caravan

Brand: Quadratec Pages: 8

Brand: K&M Pages: 3

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: Rati Pages: 2

Brand: SAN HIMA Pages: 10

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: v.link Pages: 19

Brand: GROM Audio Pages: 20

Brand: pewag Pages: 52

Brand: Blitz Pages: 4

Brand: Prorack Pages: 15

Brand: Alu-Cab Pages: 6

2013 Cadillac CTS-V

Brand: Cadillac Pages: 6

2005 HIGHLANDER

Brand: Toyota Pages: 423

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 27

Brand: Black & Decker Pages: 38

Brand: Black & Decker Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands