manualshive.com logo in svg

Diagnostic Instruments SPOT, User Manual

Share
Download
Diagnostic Instruments SPOT User Manual Download Page 63

Ch. 4 - Taking a Picture

Framing and Focusing

User's Guide to the SPOT Cooled Color Digital Camera, 6/9/98

63

resolution also decreases.  All of these factors should be considered when you select a
binning option.

The binning option on the Focus window defaults to the setting of the current image
setup.  However, you can override this setting from the Focus window by clicking on
a different setting.  The camera will use the last specified option, either from the
current image setup or the Focus window.

7.

 

Select a shutter speed limit.

The Speed option on the Focus window sets a lower limit on the update rate of the
framing window.  When you focus an image, the camera is capturing black and white
images to update the image area as you move the focus controls.  Ideally, the speed
should be as fast as possible (i.e., the Fast setting) so that the update rate is quick and
the lag time between focusing and seeing the updated image is less noticeable.
However, the brightness of the initial image plays an important part in selecting an
update rate.  Dimmer images, for example, require slower update rates in order to
produce the image quality needed for critical focusing.  The table below illustrates the
variable relationship between shutter speed, image quality, and image brightness:

Shutter Speed

Image Quality

Image Brightness Variable

Slowest (approx. 1 frames/2 secs.)

Slow (approx. 1 frames/sec.)

Medium (approx. 3 frames/sec)

Fast (approx. 5 frames/sec)

Highest

Lowest

Dimmest

Brightest

8.

 

Modify the Exposure Adjustment as needed.  Enter a value between .25 and 8, or
move the selection bar to the desired position.  The contrast of the image area changes
as you move the bar.

!

Note:  When you open the Focus window, the last entered Exposure Adjustment
value appears.  Although Exposure Adjustment on the Focus window is the same
concept as Adjustment Factor on the Image Setup window (see Chapter 3), it is
not linked to the value associated with the current image setup.

The Exposure Adjustment option enables you to overexpose or underexpose (darken
or lighten) the area of the image that you are focusing on.  This feature is designed to
help you customize your image captures.  In many cases, for example, an image has
varying levels of brightness, and you might want to lighten or darken a specific area.

9.

 

Click on the Begin option. The initial series of clicks is the camera determining the
correct exposure, as it does with the Get Image (exposure from setup) option.

10.

 

Wait for the initial clicks to end.  When the initial clicking has ended, you can begin
focusing the image.

To interrupt the process and focus on a different area, click on the Reposition button.
Use the focusing rectangle to select a different area.

Summary of Contents for SPOT

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands