Chapter 11 Summary of Parameter Settings
CT2000 Series
11-11
Pr.
Explanation
Settings
Factory
Setting
39:
Torque
command
direction
40: Force coast to stop
41: HAND switch
42:
AUTO
switch
43: Enable resolution selection (Pr.02-48)
44: Reversed direction homing
45: Forward direction homing
46: Homing (ORG)
47: Homing function enable
48: Mechanical gear ratio switch
49: Drive enable
50: Slave dEb execution
51: Selection for PLC mode bit0
52: Selection for PLC mode bit1
53: Trigger CANopen quick stop
54:
Reserved
55: Brake Released Signal
56: Local/Remote Selection
57~70:
Reserved
02-09 UP/DOWN key mode
0: up/down by the accel. /decel. time
1: up/down constant speed (Pr.02-10)
0
02-10
Constant speed. The Accel.
/Decel. Speed of the UP/DOWN
Key
0.001~1.000Hz/ms
0.001
02-11 Digital Input Response Time
0.000~30.000 sec
0.005
02-12 Digital Input Mode Selection
0000h~FFFFh (0: N.O.; 1: N.C.
)
0000
02-13 Multi-function Output 1 RY1
0: No function
11
02-14 Multi-function Output 2 RY2
1: Operation Indication
1
02-16 Multi-function Output 3 (MO1)
2: Operation speed attained
66
02-17 Multi-function Output 4 (MO2)
3: Desired frequency attained 1 (Pr.02-22)
0
02-36 Output terminal of the I/O
extension card (MO10)
4: Desired frequency attained 2 (Pr.02-24)
0
02-37 Output Terminal of I/O Extension
Card (MO11)
5: Zero speed (Frequency command)
0
02-38
Output Terminal of I/O Extension
Card (MO12)
6: Zero speed, include STOP(Frequency command)
0
02-39 Output Terminal of I/O Extension
Card (MO13)
7: Over torque 1(Pr.06-06~06-08)
0
02-40 Output Terminal of I/O Extension
Card (MO14)
8: Over torque 2(Pr.06-09~06-11)
0
02-41 Output Terminal of I/O Extension
Card (MO15)
9: Drive is ready
0
02-42 Output Terminal of I/O Extension
Card (MO16)
10: Low voltage warning
(
LV
)
(Pr.06-00)
0
02-43 Output Terminal of I/O Extension
Card (MO17)
11: Malfunction indication
0
02-44 Output Terminal of I/O Extension
Card (MO18)
12: Mechanical brake release(Pr.02-32)
0
02-45
Output Terminal of I/O Extension
Card (MO19)
13: Overheat warning (Pr.06-15)
0
02-46
Output Terminal of I/O Extension
Card (MO20)
14: Software brake signal indication(Pr.07-00)
0
15: PID feedback error
16: Slip error (oSL)
Summary of Contents for CT2000 Series
