Dell Inspiron XPS Service Manual Download Page 93

Page: 93 / 120

Back to Contents Page

Mini PCI Card

Dell™ Inspiron™ XPS Service Manual

Removing the Mini PCI Card

Replacing the Mini PCI Card

Removing the Mini PCI Card

Follow the instructions in "

Before Working Inside Your Computer

Turn the computer over and loosen the two captive screws from the cover.

Place your finger under the cover at the indentation and lift the cover open.

Disconnect the antenna cables from the Mini PCI card.

CAUTION:

If you are removing and/or installing a 2.4-GHz (802.11b, 802.11b/g) Mini PCI card, follow the instructions noted below. Only

products approved for use in your portable computer may be installed. Approved Mini PCI cards may be purchased only from Dell.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions located in the

Product Information Guide

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTE:

2.4-GHz Wireless LAN PC Cards may be removed and installed by the user.

NOTE:

If you ordered a Mini PCI card with your computer, the card is already installed. If a Mini PCI card is not already installed, go to "

Replacing the

Mini PCI Card

". If you are replacing a Mini PCI card, remove the existing card.

1 antenna cables (2)

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands