Dell Inspiron XPS Service Manual Download Page 111

Page: 111 / 120

Back to Contents Page

System Components

Dell™ Inspiron™ XPS Service Manual

Back to Contents Page

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not

covered by your warranty.

NOTICE:

Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in

reverse order.

display assembly

12 speakers

center control cover

13 subwoofer

palm rest (with touch pad)

14 optical drive

mini PCI card

15 system board

fan

16 fan

video card/thermal cooling assembly 17 microprocessor

computer base

18 microprocessor thermal cooling assembly

hard drive cage

19 MCH heat sink

PC Card reader cage

20 keyboard

10 hard drive

21 USB port board

11 battery

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Dell Inspiron XPS, Service Manual, Page: 111 / 120

Search results

Summary of Contents for Inspiron XPS

Reviews: