Dell Inspiron XPS Service Manual Download Page 19

Page: 19 / 120

Removing the Display Panel

Follow the instructions in "

Before Working Inside Your Computer

Remove the

display assembly

Remove the

display bezel

Remove the M2 x 3-mm ground screw that attaches the display-panel ground wire to the back display cover.

Remove the eight M2 x 3-mm screws (four on each side of the display panel).

Lift the display panel out of the display cover.

Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector.

Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.

Replacing the Display Panel

Reconnect the top display cable connector to the top flex-cable connector.

Reconnect the bottom flex-cable connector to the inverter connector.

Replace the display panel inside the top cover.

Replace the M2 x 3-mm ground screw that attaches the display-panel ground wire to the back display cover.

Replace the eight M2 x 3 screws (four on each side) around the display panel.

1 display grounding screw

2 display

3 M2 x 3-mm screws (8)

4 display back cover

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

1 pull-tab on bottom flex-cable connector

2 top flex-cable connector

3 display connector

4 inverter connector

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands