manualshive.com logo in svg

Dell Inspiron XPS, Service Manual, Page: 96 / 120

Share
Download
Dell Inspiron XPS Service Manual Download Page 96

Back to Contents Page

  

 

 Modem  

Dell™ Inspiron™ XPS Service Manual

 

  

Removing the Modem 

 

  

Replacing the Modem 

 

 

 

Removing the Modem  

 

 

 

 

1.

Follow the instructions in "

Before Working Inside Your Computer

."  

 

 

  

2.

Turn the computer over, loosen the two captive screws on the modem cover, and remove the cover from the computer.  
 

  

 

 

3.

Remove the M2 x 3-mm screw that attaches the modem to the system board.  
 

 

  

4.

Pull up on the pull-tab to disconnect the modem from the connector on the system board.  
 

  

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions located in the 

Product Information Guide

.

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as the back panel) on the computer.

 

NOTICE: 

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 

1  modem 

2  modem cable 

3  pull-tab 

4  screw (M2 x 3 mm) 

5  system board connector 

Summary of Contents for Inspiron XPS

























































































































Reviews:

No comments