manualshive.com logo in svg

Dell Inspiron XPS, Service Manual, Page: 64 / 120

Share
Download
Dell Inspiron XPS Service Manual Download Page 64

Back to Contents Page

  

 

 PC Card Reader Cage  

Dell™ Inspiron™ XPS Service Manual

 

  

Removing the PC Card Reader cage 

 

 

 

Removing the PC Card Reader cage  

 

 

 

 

1.

Follow the instructions in "

Before Working Inside Your Computer

."  

 

 

  

2.

Remove the 

hard drive

.  

 

 

  

3.

Remove the 

optical drive

.  

 

 

  

4.

Remove the center control cover.  
 

 

  

5.

Remove the 

keyboard

.  

 

 

  

6.

Remove the 

display assembly

.  

 

 

  

7.

Remove the 

palm rest

.  

 

 

  

8.

Disconnect the PC Card connector from the system board.  
 

  

 

 

9.

Remove the four M2 x 3-mm screws that attach the PC Card reader cage to the top of the hard drive bay.  
 

Back to Contents Page

 

 

 

 

CAUTION: 

Before you begin the following procedure, see the safety instructions in the 

Product Information Guide

.

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as the back panel) on the computer.

 

NOTICE: 

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 

1  PC Card reader cage 

2  M2 x 3-mm screws (4) 

2  PC Card reader connector 

Summary of Contents for Inspiron XPS

























































































































Reviews:

No comments