Dell Inspiron XPS Service Manual Download Page 81

Page: 81 / 120

Back to Contents Page

Subwoofer

Dell™ Inspiron™ XPS Service Manual

Removing the Subwoofer

Replacing the Subwoofer

Removing the Subwoofer

If you ordered a subwoofer with your computer, it is already installed. To remove and replace a subwoofer:

Follow the instructions in "

Before Working Inside Your Computer

Remove the

optical drive

Remove the center control cover.

Remove the keyboard.

Remove the

display assembly

Remove the

palm rest

Loosen the two captive screws that secure the subwoofer in place.

Remove the subwoofer cable connector from the system board.

Replacing the Subwoofer

Reconnect the subwoofer cable to the system board.

Place the subwoofer onto the system board.

Tighten the two captive screws that secure the subwoofer in place.

CAUTION:

Before performing the following procedures, read the safety instructions in your

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

1 subwoofer

2 subwoofer cable connector

3 system board connector

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands