manualshive.com logo in svg

Dell Inspiron XPS, Service Manual, Page: 21 / 120

Share
Download
Dell Inspiron XPS Service Manual Download Page 21

Back to Contents Page

  

 

 System Fans  

Dell™ Inspiron™ XPS Service Manual

 

  

Removing the System Fans 

 

  

Replacing the System Fans 

 

 

 

Removing the System Fans  

 

 

 

 

1.

Follow the instructions in "

Before Working Inside Your Computer

."  

 

 

  

2.

Remove the 

center control cover

.  

 

 

  

3.

Remove the 

keyboard

.  

 

 

  

4.

Remove the 

display assembly

.  

 

 

  

5.

Remove the 

palm rest

.  

 

 

 

6.

Remove the two M2.5 x 5-mm screws from each of the fans, and then remove the connectors (2 each) that connect each fan to the system board.  
 

 

  

7.

Lift each fan out of the computer.  
 

  

 

 

CAUTION: 

Before you begin the following procedure, see the safety instructions in the 

Product Information Guide

.

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as the back panel) on the computer.

 

NOTICE: 

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 

 

NOTE: 

This computer has two system fans. One is for the processor (the larger one on the left side) and the other is for the graphics card (the smaller 

one on the right side).

1  M2.5 x 5-mm screws (2) 

2  fan 

3  LED system board connector 

4  fan system board connector 

Summary of Contents for Inspiron XPS

























































































































Reviews:

No comments