Dell Inspiron XPS Service Manual Download Page 69

Page: 69 / 120

24.

Remove the three M2.5 x 5-mm screws from the system board.

25.

Remove the system board, slowly easing the connectors out of their access holes on the back and side of the computer base:

With the back of the computer facing you, grasp the upper-right corner of the system board and lift it slightly.

Pull the system board assembly away from you toward the front of the computer and slightly to the right; at the same time, use your left hand to

release the audio connectors by carefully pulling the side of the computer base slightly to the left.

Grasp the lower-right corner of the system board and slide it toward the right to remove the system board from the computer base.

Replacing the System Board

Perform all of the steps in "

Removing the System Board

" in reverse order.

Turn on the computer.

Insert the flash BIOS update program CD that accompanied the replacement system board into the optical drive. Follow the instructions that appear on
the screen.

2 PC Card connector

3 cable connector for

internal card with
Bluetooth wireless
technology

4 speaker connector

5 subwoofer connector

1 system board M2.5 x 5-mm

screws (4)

1 system board assembly

NOTICE:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in

damage to the computer.

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands