Dell Inspiron XPS Service Manual Download Page 47

Page: 47 / 120

Back to Contents Page

Center Control Cover

Dell™ Inspiron™ XPS Service Manual

Removing the Center Control Cover

Replacing the Center Control Cover

Removing the Center Control Cover

Follow the instructions in "

Before Working Inside Your Computer

Open the display all the way (180 degrees) so that it lies flat against your work surface.

Using a small flat end screwdriver, insert the screwdriver on the right side to gently pry the center control cover loose.

Gently remove the center control cover by pulling it up from right to left.

Replacing the Center Control Cover

Gently snap the cover back in place starting from left to right.

Back to Contents Page

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions located in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTICE:

The center control cover is fragile and can be damaged if extreme force is used. Be careful when removing the center control cover.

1 center control cover

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands