Dell Inspiron XPS Service Manual Download Page 112

Page: 112 / 120

Back to Contents Page

Microprocessor Thermal-Cooling Assembly

Dell™ Inspiron™ XPS Service Manual

Removing the Microprocessor Thermal-Cooling Assembly

Replacing the Microprocessor Thermal-Cooling Assembly

Removing the Microprocessor Thermal-Cooling Assembly

Follow the instructions in "

Before Working Inside Your Computer

Remove the

center control cover

Remove the

keyboard

Remove the

display assembly

Remove the

palm rest

Loosen in consecutive order the four captive screws, labeled "1" through "4," that secure the microprocessor thermal-cooling assembly to the system
board.

Lift up the microprocessor thermal-cooling assembly and remove it from the system board.

Replacing the Microprocessor Thermal-Cooling Assembly

Evenly apply thermal grease to the top surface of the microprocessor.

Place the microprocessor thermal-cooling assembly over the microprocessor.

Tighten the four captive screws, labeled "1" through "4," in consecutive order.

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

1 microprocessor thermal-cooling assembly

2 captive screws (4)

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands