Dell Inspiron XPS Service Manual Download Page 62

Page: 62 / 120

Remove the

Internal Card With Bluetooth

Wireless Technology

10.

Turn the computer top-side up and disconnect the touch-pad connector from the system board.

11.

Remove the LED board connector.

12.

Lift the palm rest and remove it from the computer.

Replacing the Palm Rest

Align the palm rest with the bottom plastics and gently snap into place.

Reconnect the touch-pad connector to the system board.

Reconnect the LED board to the system board.

Replace the coin-cell battery.

Replace the seven M2.5 x 5-mm screws on the top side of the palm rest.

Turn the computer over, and replace the eleven M2.5 x 8-mm screws on the bottom of the computer.

Replace the

Internal Card With Bluetooth

Wireless Technology

1 M2.5 x 8-mm screws (11)

1 touch-pad connector

2 LED board connector

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands