Dell Inspiron XPS Service Manual Download Page 20

Page: 20 / 120

Replace the

display bezel

Display Latch

Removing the Display Latch

Follow the instructions in "

Before Working Inside Your Computer

Remove the

display

Remove the

display bezel

Slide the latch to the right and gently lift up.

Remove the spring that attaches the latch to the display panel.

Replacing the Display Latch

Replace the spring that attaches the latch to the display panel.

Align the latch with the display panel and slide the latch to the left to secure it into place.

Back to Contents Page

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

1 spring

2 display latch

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands