manualshive.com logo in svg

Dell Inspiron XPS, Service Manual, Page: 27 / 120

Share
Download
Dell Inspiron XPS Service Manual Download Page 27

 

 

3.

Disconnect any telephone or network cables from the computer.  
 

 

  

4.

Disconnect your computer and all attached devices from their electrical outlets.  
 

 

  

5.

Close the display and turn the computer upside down on a flat work surface.  
 

 

 

6.

Slide the battery-bay latch release on the bottom of the computer and remove the battery from the bay.  
 

 

  

7.

Turn the computer top-side up.  
 

  

 

 

8.

Remove any installed PC Cards from the PC Card slot.  
 

 

Computer Orientation  

  

 

Screw Identification  

When you are removing and replacing components, print "

Screw Identification

" as a tool to lay out and keep track of the screws. The placemat provides the 

 

NOTICE: 

To avoid damaging the system board, you must remove the main battery before you service the computer. 

1  battery-bay latch release 

2  battery 

1 

front 

2 

left 

3 

back 

4 

right 

Summary of Contents for Inspiron XPS

























































































































Reviews:

No comments