Dell Inspiron XPS Service Manual Download Page 30

Page: 30 / 120

Back to Contents Page

Flashing the BIOS

Dell™ Inspiron™ XPS Service Manual

Ensure that the AC adapter is plugged in and that the main battery is installed properly.

Insert the BIOS update program CD, and turn on the computer.

Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the
computer will automatically reboot.

Press <F2> during POST to enter the system setup program.

Press <Alt> and <f> to reset the computer defaults.

Press <Esc>, select

Save/Exit

, and press <Enter> to save configuration changes.

Remove the flash BIOS update program CD from the drive and restart the computer.

Back to Contents Page

NOTICE:

Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage.

NOTE:

If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD.

NOTICE:

Do not interrupt this process once it begins. Doing so may cause system damage.

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands