Dell Inspiron XPS Service Manual Download Page 31

Page: 31 / 120

Back to Contents Page

Internal Card With Bluetooth

Wireless Technology

Dell™ Inspiron™ XPS Service Manual

Removing the Card

Replacing the Card

Removing the Card

Follow the instructions in "

Before Working Inside Your Computer

Remove the M2.5 x 8-mm screw and remove the card cover from the computer.

Pull the card out of the compartment so that you can disconnect the card from its cable and remove it from the computer.

Replacing the Card

Connect the card to the cable and then carefully insert the card into the compartment.

Replace the card cover and the screw.

Replace the battery.

Back to Contents Page

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTE:

If you ordered an internal card with Bluetooth wireless technology with your computer, the card is already installed.

1 card connector

2 internal card with Bluetooth wireless technology

3 card door

3 M2.5 x 8-mm screw

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands