Dell Inspiron XPS Service Manual Download Page 36

Page: 36 / 120

Back to Contents Page

Display

Dell™ Inspiron™ XPS Service Manual

Display Assembly

Display Bezel

Display Panel

Display Latch

Display Assembly

Removing the Display Assembly

Follow the instructions in "

Before Working Inside Your Computer

Turn the computer over and loosen the two captive screws on the Mini PCI card cover.

Disconnect the antenna cables from the Mini PCI card.

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTE:

If a Mini PCI card is installed, you will need to remove the antenna cables from the card. If one is not installed, remove the antenna cables from

their secured location.

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands