Dell Inspiron XPS Service Manual Download Page 37

Page: 37 / 120

Turn the computer top-side up.

Remove the

center control cover.

Open the display all the way (180 degrees) so that it lies flat against the work surface.

Use the pull-tab to disconnect the display cable, and then disengage the display cable from the cable channel.

Use the pull-tab to disconnect the LED cable, and then disengage the LED cable from the cable channel.

Remove the four M2.5 x 5-mm screws (two on each side) that connect the display to the computer base.

antenna cables

1 display cable pull-tab

2 M2.5 x 5-mm screws (4)

3 Mini PCI card antenna cables (2)

4 display cable connector on system board

1 LED cable

2 Mini PCI card antenna cables

NOTE:

When removing the display assembly, carefully thread the Mini PCI card antenna cables through the computer base.

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands