Danfoss VLT Flow Drive FC 111 Programming Manual Download Page 85

Page: 85 / 214

[168] Drive in hand mode

The output is high when the drive is in hand-on mode (as indicated by the LED light above
[Hand On]).

[169] Drive in auto mode

The output is high when the drive is in auto-on mode (as indicated by the LED light above [Auto
On]).

[188] AHF Capacitor Con-

nect

Connect or disconnect AHF capacitor.

[190] No-Flow

A no-flow condition has been detected. See

parameter group 22-2* No-Flow Detection

[191] Dry Pump

A dry-pump condition has been detected. Enable the function in

parameter 22-26 Dry Pump

Function

[192] End Of Curve

An end-of-curve condition has been detected. Enable the function in

parameter 22-50 End of

Curve Function

[193] Sleep Mode

The drive/system has entered sleep mode. See

parameter group 22-4* Sleep Mode

[194] Broken Belt Function

A broken-belt condition has been detected. Enable the function in

parameter 22-60 Broken Belt

Function

[196] Fire Mode

The drive is operating in fire mode. See

parameter group 24-0* Fire Mode

[198] Drive Bypass

To be used as a signal for activating an external electromechanical bypass, switching the motor
directly on line. See

parameter group 24-1* Drive Bypass

[200] Full capacity

The drive enters full capacity mode.

[201] Pump 1 running

Pump 1 is running.

[202] Pump 2 running

Pump 2 is running.

[203] Pump 3 running

Pump 3 is running.

[204] Pump 4 running

Pump 4 is running.

[205] Pump 5 running

Pump 5 is running.

[211] Cascade Pump 1

Cascade pump 1 is running.

[212] Cascade Pump 2

Cascade pump 2 is running.

[213] Cascade Pump 3

Cascade pump 3 is running.

[214] Cascade Pump 4

Cascade pump 4 is running.

[215] Cascade Pump 5

Cascade pump 5 is running.

5-34 On Delay, Digital Output

Default value: 0.01 s

Parameter type: Range

2-setup: All setups

Conversion index: -2

Data type: u_int16

Change during operation: True

Enter the delay time before the digital output is switched on. The digital output (terminal 42/45) condition must not be interrupted
during the delay time.

Table 140: Range:

Min: 0 s

Max: 600 s

Default value: 0.01 s

AU363928304090en-000101 / 130R0982 | 85

Parameters

VLT® Flow Drive FC 111

Programming Guide

Summary of Contents for VLT Flow Drive FC 111























































































































































































































Search results

Summary of Contents for VLT Flow Drive FC 111

Reviews:

Related manuals for VLT Flow Drive FC 111

Brands by name

Popular brands

Danfoss VLT Flow Drive FC 111, Programming Manual

Search results

Summary of Contents for VLT Flow Drive FC 111

Reviews:

Related manuals for VLT Flow Drive FC 111

Brands by name

Popular brands