Dahua Technology DHI-IVSS7008 User Manual Download Page 326

Page: 326 / 381

User's Manual

306

System service

Description

Password

Expires in

Configure the password expiration interval. The Device prompts you to

change the password when the password expires.

Audio/Video

Transmission

Encryption

When this function is enabled, stream transmission will be encrypted.

We recommend you enable this function. Otherwise you might risk data
leakage.

RTSP over TLS

Enable this function to encrypt stream transmission.
You are recommended to enable this function. Otherwise you might risk data

leakage.

Private Protocol

Authentication

Mode

Select a private protocol authentication mode between security mode and

compatible mode. Compatible mode is recommended.

Step 3

Click Save.

8.6.5 Configuring Firewall

Enhance network and data security by prohibiting Ping and half-connection.

●

PING Prohibited: When PING Prohibited is enabled, the device does not respond to Ping

requests.

●

Anti Half Connection: When Anti Half Connection is enabled, and the device can provide service

normally under half-connection attack.

Step 1

Click

, or click

on the configuration page, and then select SECURITY > Firewall.

Figure 8-97 Firewall

Step 2

Click

to enable PING Prohibited or Anti Hal Connection.

Step 3

Click Save.

8.6.6 Configuring Time Synchronization Permission

Configure permissions of time synchronization actions from other devices or servers.
Step 1

Click

, or click

on the configuration page, and then select SECURITY > Synch Time.

Step 2

Click

to enable time synchronization restriction.

Step 3

Select Allowlist or Blocklist.

Summary of Contents for DHI-IVSS7008






























































































































































































































































































































































































Search results

Summary of Contents for DHI-IVSS7008

Reviews:

Related manuals for DHI-IVSS7008

Brands by name

Popular brands

Dahua Technology DHI-IVSS7008, User Manual

Search results

Summary of Contents for DHI-IVSS7008

Reviews:

Related manuals for DHI-IVSS7008

Brands by name

Popular brands