Connection Technology Systems VRG-21412-WF-G SERIES User Manual Download Page 15 | Manualshive

Page: 15 / 63

background image

15

Fiber Information

Connector:

View-only field that shows the fiber connector type.

Speed:

View-only field that shows the speed of this fiber transmission.

Wave Length:

View-only field that shows the receiving and transmitting wave length of this

fiber.

Distance:

View-only field that shows the maximum distance that this fiber can reach.

WAN

WAN Type:

View-only field that shows the WAN port type (Static IP or DHCP assigned) of

the WLAN VoIP Residential Gateway.

MAC Address:

View-only field that shows the unique and permanent MAC address

assigned to the WLAN VoIP Residential Gateway. The factory default MAC address of your
WLAN VoIP Residential Gateway can not be changed.

IP Address:

View-only field that shows the unique IP address of WAN interface.

Subnet Mask:

View-only field that specifies the subnet mask to be used with the WLAN

VoIP Residential Gateway IP address. The default subnet mask values for the three Internet
address classes are as follows:



Class A: 255.0.0.0



Class B: 255.255.0.0



Class C: 255.255.255.0

«
...
13
14
15
16
17
...
»

Summary of Contents for VRG-21412-WF-G SERIES
































































Reviews:

No comments

Related manuals for VRG-21412-WF-G SERIES

Brand: TANDBERG Pages: 63

Brand: JBM electronics Pages: 29

Brand: Garmin Pages: 8

Brand: Arris Pages: 2

Brand: THOMSON Pages: 54

Brand: THOMSON Pages: 74

Brand: Logic IO Pages: 36

Brand: Planet Networking & Communication Pages: 38

VGW 20FS Series

Brand: Planet Networking & Communication Pages: 84

Brand: Wildix Pages: 11

Brand: Zycoo Pages: 15

Brand: Zycoo Pages: 22

HomePortal 3700HGV

Brand: 2Wire Pages: 4

Brand: 24online Pages: 8

Brand: RTA Pages: 64

Brand: RTA Pages: 66

Brand: RTA Pages: 81

GW8600 Service Managed Gateway

Brand: virtual access Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands