Connection Technology Systems VRG-21412-WF-G SERIES User Manual Download Page 44

Page: 44 / 63

2.7 SIP Management

Select

SIP Management

from the

Main Menu

, the sub-item –

Basic setting

Account

setting

and Server setting

– will show up.

2.7.1 Basic Setting

Select

Basic Setting

from the

SIP Management

menu,

then

Basic Settings

screen page

appears.

SIP Port Number:

Specify the IP phone number. The number ranges from 1024 to 65535.

The default setting is 5060.

Session Timer:

Specify the time interval in seconds to refresh SIP. The default setting is

1800 seconds.

Media Port Start:

Specify the media port Start number for RTP.

Media Port End:

Specify the media port End number for RTP.

RTCP:

Specify the RTCP port number.

Transport:

Choose either UDP or TCP. The default SIP transport type is UDP.

SIP Time Interval:

Specify SIP time interval in milliseconds. The default setting is 500 msec.

Time out for Invite:

Specify the time interval for Invite message timeout. The Invite

message will be dropped if a response is not received within the designated time.

Time out for Ring back:

Specify the timeout time for ring back.

Summary of Contents for VRG-21412-WF-G SERIES
































































Search results

Summary of Contents for VRG-21412-WF-G SERIES

Reviews:

Related manuals for VRG-21412-WF-G SERIES

Brands by name

Popular brands

Connection Technology Systems VRG-21412-WF-G SERIES, User Manual

Search results

Summary of Contents for VRG-21412-WF-G SERIES

Reviews:

Related manuals for VRG-21412-WF-G SERIES

Brands by name

Popular brands