Connection Technology Systems VRG-21412-WF-G SERIES User Manual Download Page 46

Page: 46 / 63

2.7.3 Server Setting

Select

Server Setting

from the

SIP Management

menu,

then

Server Setting

screen page

appears.

Authentication Expired Time:

Specify SIP authentication expired time in seconds. The

default setting is 3600 seconds.

Use Outbound Proxy for all messages:

Tick the checkbox to enable outbound proxy.

Register:

Tick the checkbox to enable registration.

Register Server Address:

Specify the registration server address.

Register Server Port:

Specify the registration server port.

Proxy Address:

Specify the proxy address of the SIP server.

Proxy Port:

Specify the proxy port of the SIP server.

Use Outbound Proxy:

Tick the checkbox to use outbound proxy.

Outbound Proxy Address:

When outbound proxy is enabled, you need to further specify

the IP address of SIP outbound proxy server.

Outbound Proxy Port:

When outbound proxy is enabled, you need to further specify the

port number of outbound proxy server.

DNS SRV Support:

Tick the checkbox to enable DNS SRV support. When enabled, calls

will be routed to the proxy address specified.

Summary of Contents for VRG-21412-WF-G SERIES
































































Search results

Summary of Contents for VRG-21412-WF-G SERIES

Reviews:

Related manuals for VRG-21412-WF-G SERIES

Brands by name

Popular brands

Connection Technology Systems VRG-21412-WF-G SERIES, User Manual

Search results

Summary of Contents for VRG-21412-WF-G SERIES

Reviews:

Related manuals for VRG-21412-WF-G SERIES

Brands by name

Popular brands