manualshive.com logo in svg

Connection Technology Systems VRG-21412-WF-G SERIES, User Manual, Page: 43 / 63

Share
Download
Connection Technology Systems VRG-21412-WF-G SERIES User Manual Download Page 43

43 

 

2.6 Switch Monitor 

Select

 Switch Monitor

 from the 

Main Menu

, the sub-item – 

Switch Port State

 – will show 

up. 
 

 

 

Port State Polling: 

Tick the checkbox to automatically refresh port status.

 

 
Polling Time: 

Specify time interval in seconds to automatically refresh port status. 

 

 
Media Type:

 View-only field that shows whether each port is a copper port or fiber port. 

 
Port State: 

View-only field that shows whether each port is enabled or not.

 

 

Link State: 

View-only field that shows whether each port is link up or down. 

 

Speed (Mbps): 

View-only field that shows the speed of the link-up port(s). 

 

Duplex:

  View-only field that shows whether the link-up port is in full or half duplex mode. 

 

Flow  Control:

  View-only  field  that  shows  whether  each  port’s  flow  control  function  is 

enabled or disabled. 

 
 

Summary of Contents for VRG-21412-WF-G SERIES
































































Reviews:

No comments