Comnet CNGE20MS Installation And Operation Manual Download Page 96 | Manualshive

Page: 96 / 144

Comnet CNGE20MS Installation And Operation Manual Download Page 96

INS_CNGE24MS-OB(M,S)_REV–

09/12/12 PAGE 96

INSTALLATION AND OPERATION MANUAL

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

RADIUS Accounting Servers

Label

Description

#

The RADIUS server number. Click to navigate to detailed statistics for this server.

IP Address

The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this
server.

Status

The current status of the server. This field takes one of the following values:
Disabled: The server is disabled.
Not Ready: The server is enabled, but IP communication is not yet up and running.
Ready: The server is enabled, IP communication is up and running, and the RADIUS
module is ready to accept accounting attempts.
Dead (X seconds left): Accounting attempts were made to this server, but it did not
reply within the configured timeout. The server has temporarily been disabled, but will
get re-enabled when the dead-time expires. The number of seconds left before this
occurs is displayed in parentheses. This state is only reachable when more than one
server is enabled.

«
...
94
95
96
97
98
...
»

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands