manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 87

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 87

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Label

Description

VLAN ID Filter

Specify the VLAN ID filter for this ACE.  
Any: No VLAN ID filter is specified. (VLAN ID filter status is “don’t-care”.)  
Specific: If you want to filter a specific VLAN ID with this ACE, choose this value. A field 
for entering a VLAN ID number appears.

VLAN ID 

When “Specific” is selected for the VLAN ID filter, you can enter a specific VLAN ID number. 
The allowed range is 1 to 4095. A frame that hits this ACE matches this VLAN ID value.

Tag Priority

Specify the tag priority for this ACE. A frame that hits this ACE matches this tag priority. 
The allowed number range is 0 to 7. The value Any means that no tag priority is specified 
(tag priority is “don’t-care”.)

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands