manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 137

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 137

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

SNMP

SNMP>

Trap Inform Retry Times [<retries>]
Trap Probe Security Engine ID [enable|disable]
Trap Security Engine ID [<engineid>]
Trap Security Name [<security_name>]
Engine ID [<engineid>]
Community Add <community> [<ip_addr>] [<ip_mask>]
Community Delete <index>
Community Lookup [<index>]
User Add <engineid> <user_name> [MD5|SHA] [<auth_password>] [DES]  
[<priv_password>]
User Delete <index>
User Changekey <engineid> <user_name> <auth_password> [<priv_password>]
User Lookup [<index>]
Group Add <security_model> <security_name> <group_name>
Group Delete <index>
Group Lookup [<index>]
View Add <view_name> [included|excluded] <oid_subtree>
View Delete <index>
View Lookup [<index>]
Access Add <group_name> <security_model> <security_level>  
[<read_view_name>] [<write_view_name>] 
Access Delete <index>
Access Lookup [<index>]

Firmware

Firmware>

Load <ip_addr_string> <file_name>

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands